How to Cut a Long Sleeve Shirt: A Step-by-Step Guide

Scissors cutting a long sleeve shirt on a table

A long sleeve shirt you no longer wear can become a favorite summer top with nothing more than a pair of scissors and a ruler. Cutting sleeves is one of the easiest clothing alterations to try, and the cotton jersey in most tees is forgiving. Here is a clear, careful way to do it.

What you need

  • Sharp fabric scissors (kitchen scissors tend to chew the edge)
  • A tape measure or ruler
  • Tailor’s chalk, a fabric pen or a bar of soap
  • Pins
  • A shirt you do not mind experimenting on
  • Optional: needle and thread, or a sewing machine

Step 1: Decide the final length

Do you want short sleeves, cap sleeves, or sleeveless? Put the shirt on and mark where you want the hem with a pin. For a classic short sleeve, aim for around the middle of your upper arm. Remember you will lose a little fabric if you fold a hem, so mark slightly longer than you think.

Step 2: Lay the shirt flat

Smooth it on a table with the sleeves out straight. Fold the shirt in half along the center so both sleeves line up. That lets you cut both at once and keeps them even.

Step 3: Measure and mark

Measure from the shoulder seam down to your chosen length. Mark with chalk at a few points, then join them into a gentle line. The line should run straight across, but a slight curve can look more natural around the underarm.

Step 4: Cut slowly

Cut along your line using long, smooth strokes rather than short snips. Lift the fabric as little as possible to avoid wobbles. When done, unfold and compare the two sleeves. Trim any difference.

Step 5: Finish the edge

Jersey does not fray the way woven cloth does, so you can leave the raw edge. It will curl slightly, which many people like. For a tidier look, fold the edge over by around half an inch and stitch it with a zigzag or a stretch stitch. Stretch stitches stop the thread from snapping when the fabric moves.

No-sew option

Iron-on hem tape works for light-duty edges. It is fast, though it may loosen after many washes.

Other cuts you can try

Style How to do it
Short sleeve Cut at mid-upper arm and hem
Cap sleeve Cut closer to the shoulder seam
Sleeveless Cut just outside the seam, leaving a thin margin
Crop Shorten the body, not the sleeves

Common mistakes

The most frequent problem is cutting too short. You can always remove more, but you cannot put fabric back. Another is cutting each sleeve separately by eye, which leaves them uneven. Folding the shirt first avoids that.

Also, check the fabric. Knit jersey behaves nicely. A thin woven shirt will fray and needs a proper hem. For tips on adjusting tees, see our guide to modifying crew neck t-shirts.

Related projects

If you enjoy altering clothes, you might like our walkthroughs on sewing a polo shirt and stretching sweatshirt sleeves. They use similar basic skills.

Washing afterward

Wash the finished top as usual, ideally on a gentle cycle. The edge may curl more after the first wash, then settle. If you hemmed it, press it lightly with an iron on a setting suited to the fabric.

A last tip

Practice on an old tee before you cut a shirt you love. One bad cut on a favorite piece is a lesson you can avoid.

Choosing the right shirt

Stretch jersey, thin cotton and soft blends are the easiest to cut and finish. Ribbed or thick sweatshirt fabric also cuts well, though the thicker edge may roll. Avoid shirts with seams you want to keep around the cuff, such as button cuffs, unless you plan to take them off entirely.

Check the print or tag too. If a graphic runs down the sleeve, cutting will remove it. Plan the line around what you want to keep.

Making the edge curl or lie flat

When jersey is cut across the grain, the edge curls toward the right side of the fabric. If you cut along the lengthwise grain it curls differently. You can use the curl as a design feature, for a casual rolled look. If you want a flat edge, stitch a narrow hem or press with steam and a clean cloth.

Adding small details

A few easy touches make the top look purchased rather than cut. Fold the sleeve up twice to make a cuff, then tack it with a few hand stitches. Snip the neckline slightly wider for a relaxed fit, just a little at a time. Or leave a clean raw edge and add a patch or a stitch line in a contrasting thread. Small changes on a plain base can make it distinct.

Using the leftover fabric

Do not throw away the cut sleeves. Jersey scraps make good cleaning rags, headbands, hair ties and stuffing for small cushions. Cut a long strip and twist it for a simple scarf or braid it into a bracelet. A little creativity turns waste into something useful, and it keeps textile scraps out of the bin.

If you really want to keep the sleeves for another project, fold them flat and store them with your sewing supplies.

FAQ

Will the cut edge unravel?

Knit jersey fabric usually does not fray, so the edge just curls. Woven fabrics need a hem.

Do I need a sewing machine?

No. You can hand stitch, use hem tape, or leave a jersey edge raw.

Can I cut any long sleeve shirt?

Most cotton or cotton blend tees work well. Check delicate or very thin fabrics first.

Photo: Photo by Lance Cpl. Brennan Priest / Wikimedia Commons (Public domain)