How to Sew a Polo Shirt: A Step-by-Step Guide

Sewing machine with knit fabric and polo pattern pieces

A project worth trying

A polo has more parts than a basic tee. There is a collar, a placket with buttons and usually a hem with side vents. That makes it a good step up once you are comfortable sewing knit fabric. It will take patience, but nothing here is out of reach.

What you need

  • A polo shirt pattern in your size from a pattern company, or an old polo to trace
  • Knit fabric such as cotton piqué or cotton jersey with some stretch
  • Ribbed collar and cuff trim, or self-fabric collar
  • Lightweight fusible interfacing for the placket
  • Buttons, usually two or three
  • A sewing machine with ballpoint or stretch needles
  • Polyester thread, clips and a pressing cloth

Choosing the fabric

Piqué is the classic polo fabric, with a textured surface. Jersey makes a softer, flatter polo. Wash and dry the fabric before cutting, in the way you will wash the finished shirt, to deal with shrinkage in advance.

Cut carefully

Lay the fabric on a flat surface with the grain running straight. Follow the pattern layout. Knit fabric slips, so use pattern weights or plenty of pins, and cut with sharp shears or a rotary cutter. Mark the placket and button positions on the fabric.

Steps

1. Prepare the placket

Fuse interfacing to the placket pieces. Sew and slit the front opening following your pattern’s instructions. Take care at the point of the slit. This is the part most beginners find fiddly, so read the pattern twice and practise on scrap fabric.

2. Join the shoulders

Sew the front to the back at the shoulders, right sides together. A narrow zigzag or a stretch stitch lets the seam give a little. Clear tape or stay tape along the shoulder seam stops it from stretching out.

3. Attach the collar

Pin the collar around the neckline, matching centre points. Stretch the neckline slightly if the collar is ribbed. Sew slowly, then trim the seam allowance and press toward the shirt. A tidy collar is what makes a polo look right. If your finished collar misbehaves, see how to fix polo shirt collars.

4. Set in the sleeves

Pin the sleeve cap to the armhole, matching notches. Sew with the sleeve on top. Easing knit fabric is much easier than woven, so you should not need to gather much.

5. Sew the sides and sleeves

Sew from the cuff to the underarm and down the side in one pass. Leave the side vent openings free if your pattern has them.

6. Hem and finish

Hem with a twin needle for a stretchy professional finish, or a zigzag. Finish the sleeve ends the same way, or attach ribbed cuffs. Add buttonholes on the placket and sew on the buttons. Press everything, using a cloth to protect the fabric.

Tips for knit fabric

  • Use a ballpoint or stretch needle to avoid skipped stitches
  • Lower presser foot pressure if the fabric stretches while feeding
  • Use a walking foot if you have one
  • Do not pull the fabric as you sew
  • Test stitches on a scrap first

Fitting and finishing

Compare your measurements to the pattern size chart before cutting. Polos are normally meant to be fitted but not tight. If you plan to wear it tucked, see the guide to tucking in a polo for length ideas.

Care

Wash your handmade polo in cool water and dry on low heat or flat. If it ends up too small after all, our guide to how to shrink a polo shirt covers the reverse problem, shrinking one that is too large.

If it goes wrong

Everyone’s first polo has flaws. A wobbly placket or a crooked collar is normal. Unpick, press and try again, or wear it as a learning piece. The next one will look better.

Planning before you start

Read the whole pattern first. Polo instructions can look intimidating, but each step is short. Make a test version from cheap fabric if you can, because the placket and collar are easier to understand on a practice piece than on your good fabric.

Choosing a size

Use your chest measurement, not your usual shop size. Pattern sizes and ready-to-wear sizes do not always match. Check the finished garment measurements, if the pattern lists them, and think about how fitted you want the shirt to be.

Tools that make it easier

A few small extras help a lot. Wonder clips hold knit layers without leaving holes, a seam ripper is your best friend, and a tailor’s ham or rolled towel helps you press curved seams like the collar. A clapper or simply a firm press with steam sets collars flat.

Where to go from here

Once you can make a basic polo, try a longer-sleeved version, a contrast collar or a different fabric. You can also customise the fit. A shorter body, a slimmer sleeve or a different vent shape are all simple changes.

Pressing as you go

Press each seam before you cross it with another. On knit fabric, use steam and a light touch rather than sliding the iron, which stretches the cloth. A well-pressed seam makes the next step easier and gives the finished shirt a neater look. Take your time, and the result will look closer to something from a shop than a first attempt has any right to.

FAQ

What fabric is best for a first polo?

A stable cotton piqué or medium-weight jersey with a bit of stretch is easiest to handle.

Can I sew a polo without a serger?

Yes. A regular machine with a stretch stitch or narrow zigzag works well.

How long does it take?

Allow a few hours for a first attempt, and longer if you are new to knit fabric.

Photo: Unknown authorUnknown author or not provided / Wikimedia Commons (Public domain)